Materials List for Straight Modules

 

The following materials will build two (2) 2 ft x 4 ft module tables*.

 

I. Wood

 

1. Two 2 ft x 4 ft x 5/8 in good-one-side plywood (table decks - one 4 ft x 8 ft sheet will build 4 tabes but each deck will be 1/8 in narrow)

2. Eight 1 in x 4 in x 48 in  (frame side and top support pieces). Must be straight and solid.

            3. Two 2 in x 2 in x 8 ft (eight legs).

            4. Two 4 ft x 17.5 in tempered Masonite or 1/4 in smooth one side plywood (sky boards)

            5. 1/4 in x 4 in x 8 ft plywood or other similar material (leg cross braces)

            6. Four 3/4 in x 4 in plywood table ends.

            7. 12 ft of 1 in x 2 in (for sky board braces, must be straight)

           

II. Hardware

            1. Six 5/16 in x 1 3/4 in bolts (to mount sky boards)

            2. Eight  5/16 in x 2 1/2 in bolts (hold legs open)

            3. Fourteen 1/4 in washers (tight fit on 5/16 in bolts)

4. Thirty 5/16 in tee nuts (for leg bolts, sky board and eye bolts - 3/8 tee nuts and eye bolts may be used for leg height)

            5. Eight 5/16 or 3/8 in x 6 in eye bolts (table height adjustment)

            6. Twenty four 2 in drywall screws (3 per frame corner)

            7. Sixteen 1 in drywall screws (leg cross braces)

            8. Twenty four 1½ in dry wall screws (deck to frame on 1 ft centers)

            9. Forty eight 1 in #6 flathead screws (for leg hinges)

            10. Eight  4 in strap hinges (leg folding joints)

            11. Four 1 in #8 self starting screws (hold power strip)

12. Two sets (8) Anderson Powerpole plugs

            13. Eight spring-clip cup hooks (retain track cable ends)

14. Eight 5 ft lengths of #12 or #14 stranded wire, 2 red, 2 black.2 white. 2 yellow

            15. Two ft of #26 solid core hook-up wire (drops from track to power cables)

            16. Small metal ‘L’ bracket (leg lock)

            17. Thirty two 1 1/4 in #6 metal screws (retain tees on leg ends)

             18. Eight (8) inch of five-eights (5/8) inch OD PVC pipe tapered at one end fo alignment pins.

 

IV. Track components

            1. Three 3 ft (or 1 meter) pieces of code 100 flex track and 4 rail joiners

     

 

IV. Miscellaneous

            1. Bottle of very good quality wood glue (table corners, deck to frame and skyboard supports, etc.)   

            2. Two electrical power strips with 5 ft cords (or one with 8 ft cord on left hand table)

            3. 3 inch by 3 inch 3/8 in thick plywood scraps (for leg pads)

            4. 8 3 inch strip  of 1 in hook side Velcro (for skirt support)

            5. Staples or other wire retainers (to hold wires to underside of table top). No drooping wires, please.

           

   

 

IV. Notes:
            1. Depending on the module design devised by a given member, any of the materials listed above may vary. However construction must meet Club standards, be evaluated by the Standards Committee for compliance to the standards and modules must be fully compatible operationally.

Module Construction                 HOME

Home